V-Tec AT16/C5 Especificaciones Pagina 35
- Pagina / 94
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Si2400
Rev. 1.3 35
answer (e.g. 500 = 01) or Bellcore CID will function
normally.
Basic Command
ATDT<phone number>!7<tone pulse digits 0-9, B-
F><CR>
Result codes after dialing
t Dial tone detected
, Phone number dialed—start of initial
intermessage time
r Ringback tone detected
b Busy tone detected
c Handshake Tone detected in S39 (CDT)
time window and present for S38[4:2]
(HMT) msec
N Handshake Tone not detected per above
Result codes after “c” received
, Message sent—start of intermessage time
K Kissoff Tone detected in S36[3:2] (IDKT)
time window and present for S38[4:2] (HMT)
msec
^ Kissoff Tone not detected per above
N Intermessage timeout defined in S36[3:2]
(IDKT) elapsed. A second message received
after the “,” is sent at this time.
Table 19. !7 Parameters
S-Register Bits Name Function
S1F Alarm 3 Reconfigured from ATTD in !7 mode.
7:5 KOT Kissoff timeout.
4:0 IMT Intermessage timing.
S2B 7:0 DTL Reconfigured from DTL in !7 mode to pulse on time (5/3 ms units).
S2C 7:0 DTTO Reconfigured from DTTO in !7 mode to pulse off time (5/3 ms units).
S2D 7:0 SDL Reconfigured from SDL in !7 mode to pulse interdigit time (5/3 ms units).
S2E 7:0 RTCT Reconfigured from RTLT in !7 mode to handshake end to data TX delay
(10 ms units).
S36 Alarm 1 Reconfigured from SKDTL in !7 mode.
7:6 POF Pulse off time.
5:4 PON Pulse on time.
3:2 IDKT Intermessage delay and Kissoff timeout.
1:0 IT Interdigit timing.
S38 Alarm 2 Only used in !7 mode.
7 DBD Delay before data.
6:5 DCF Data carrier frequency.
4:2 HMT Handshake minimum tone.
1:0 HF Handshake frequency.
S39 7:0 CDT Reconfigured from CDT in !7 mode to handshake tone timeout.
- Features 1
- Applications 1
- Description 1
- Functional Block Diagram 1
- 2 Rev. 1.3 2
- TABLE OF CONTENTS 3
- 1. Electrical Specifications 4
- Table 2. Loop Characteristics 5
- Table 3. DC Characteristics 6
- Table 4. DC Characteristics 6
- Table 5. AC Characteristics 7
- for K-Grade, T 8
- –40 to 85°C for B-Grade) 8
- = –40 to 85°C for B-Grade) 9
- 10 Rev. 1.3 10
- 3. Bill of Materials 11
- 12 Rev. 1.3 12
- 4. Analog Input/Output 13
- 5. Functional Description 14
- 5.1. Digital Interface 15
- 16 Rev. 1.3 16
- 5.3. Low Power Modes 17
- 5.4. Global DAA Operation 17
- 18 Rev. 1.3 18
- Rev. 1.3 19 19
- 20 Rev. 1.3 20
- 5.6. Loop Current Detection 21
- 5.7. Carrier Detect/Loss 21
- 5.8. Overcurrent Detection 21
- 5.11. PCM Data Mode 23
- Figure 10. Signal Routing 24
- 5.12. Analog Codec 25
- 5.14. V.42 HDLC Mode 26
- 5.15. Fast Connect 27
- Table 16. MCKR Configurations 28
- 6.1. Command Line Execution 29
- 30 Rev. 1.3 30
- 6.4. S-Register Control 31
- 32 Rev. 1.3 32
- 6.5.4. A1 34
- 6.5.5. !2 34
- 6.5.6. !7 34
- Table 19. !7 Parameters 35
- Figure 12. !7 Security Timing 36
- Progress 37
- S19 S1A S1B S16 S17 S18 38
- Table 23. DTMF 39
- 7.1. DSP Registers 40
- SE8 SE6 SE5 41
- DSP Reg. Addr 41
- 7.2. Call Progress Filters 42
- 8. S Registers 43
- 44 Rev. 1.3 44
- Rev. 1.3 45 45
- 46 Rev. 1.3 46
- Rev. 1.3 47 47
- 50 Rev. 1.3 50
- Rev. 1.3 51 51
- 52 Rev. 1.3 52
- Rev. 1.3 53 53
- 54 Rev. 1.3 54
- Rev. 1.3 55 55
- 56 Rev. 1.3 56
- 58 Rev. 1.3 58
- Kissoff Tone Detect Length) 58
- Rev. 1.3 59 59
- 60 Rev. 1.3 60
- Rev. 1.3 61 61
- 62 Rev. 1.3 62
- Rev. 1.3 63 63
- Rev. 1.3 65 65
- 66 Rev. 1.3 66
- Rev. 1.3 69 69
- 70 Rev. 1.3 70
- Rev. 1.3 71 71
- 72 Rev. 1.3 72
- Rev. 1.3 73 73
- 74 Rev. 1.3 74
- Rev. 1.3 75 75
- 76 Rev. 1.3 76
- Rev. 1.3 77 77
- DAA Isolation Barrier 78
- Emissions/Immunity 78
- DC Termination 79
- AC Termination 80
- Ringer Impedance 80
- DTMF Dialing 80
- Pulse Dialing 80
- Billing Tone Detection 80
- Symbol Value 81
- In-Circuit Testing 82
- Compliance Test Commands 83
- Introduction 84
- APPENDIX C—UL1950 3RD EDITION 85
- 9. Pin Descriptions: Si2400 86
- Rev. 1.3 87 87
- 10. Pin Descriptions: Si3015 88
- Receive Input 89
- Filter 2 89
- Pin # Pin Name Description 89
- 11. Ordering Guide 90
- Millimeters 91
- Revision 1.1 to Revision 1.2 92
- Revision 1.2 to Revision 1.3 92
- Rev. 1.3 93 93
- CONTACT INFORMATION 94
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad V-Tec AT16/C5
(19 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.122 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales